New Directv Box How to Get Remote to Work Again
Is your DIRECTV remote not responding? It happens to everyone. Perhaps it got dropped one also many times, or maybe y'all're trying to utilize an old remote with a new box. Either fashion, y'all may need to reset information technology. No thing which remote you take, every bit long as information technology has a DIRECTV logo on it at that place'southward a very piece of cake style to reset information technology.
First things kickoff: supervene upon the batteries
Expressionless or weak batteries are almost always the problem with remotes. Even if the remote is working some of the time, change the batteries before doing anything else. Weak batteries can crusade poor signals that cause issues. Put in a fresh pair of batteries. Trust me, you'll be glad you did.
How to reset the erstwhile-school white remote
Does your remote await like the one above? This remote was included with every DIRECTV box from 2003 until 2014 and is still included with some DIRECTV boxes today. It's easy to reset.
If y'all are able to utilize the front console of your receiver:
- Printing MENU then pointer downwardly to Settings&Help and press SELECT.
- And so arrow over to Settings and printing SELECT again.
- Finally, arrow down to Remote Control and press SELECT.
- Make sure Reset Remote is highlighted. Press SELECT.
- Depending on your setup, this may be automatic or y'all may have to enter codes into your remote.
If you can't control the receiver at all, here'due south the manual method.
On the remote, Press and hold MUTE and SELECT at the same time until the low-cal flashes three times. Then press Printing 9 8 1 and SELECT. The remote will flash 4 times and should now be reset.
RF remotes
If you accept set the receiver to RF mode, you will have to modify it to IR manner or set the remote dorsum to RF mode. There'due south a comprehensive tutorial here, but here's the easy version:
- Make sure the summit slider is in the DIRECTV mode (far left.)
- Printing and holdMUTE andSELECT until the light on the remote flashes twice.
- So press 9 6 aneand press theAqueduct Up push button.
- Enter the last half dozen digits of your receiver ID and pressSELECT.(This is on a green sticker on the receiver or you lot tin can go it from your "My Equipment" page at DIRECTV.com.
- PressSELECT i more than fourth dimension.
If you need to alter other settings that are specific to the receiver, like the receiver manner (for instance, if the receiver is set to one of the "other modes" that allow more than one receiver to be used in the same room, you should now be able to use your remote to get into the programming and advanced menus on the receiver.
Genie Remotes
If your remote looks like this, the procedure is like. This remote is standard for all Genie hardware made since 2014. Most Genie devices don't have forepart panel buttons, so yous tin't go that road. If yous are able to use your remote at all, you tin can endeavor the menus. Sometimes property information technology very close to the DIRECTV box can help.
- Printing MENU so arrow down to Settings.
- Then arrow over to Remote Control and press SELECT.
- Arrow down to Program Remote and printingSELECT.
- Make sure Reset Remote is highlighted. Printing SELECT.
- Depending on your setup, this may be automatic or yous may have to enter codes into your remote.
If you lot tin't control the receiver at all, the manual method is the aforementioned as the other style of remote:
On the remote, Press and hold MUTE and SELECT at the same time until the light flashes 3 times. Then press Press nine 8 one and SELECT. The remote will wink four times and should now exist reset.
Programming for RF
Programming the Genie remote for RF is much, much easier. Starting time, make sure the Genie box is on. Then hold down MUTE andENTER at the same time while pointing the remote at the Genie box. Remember, that'due south the ENTER push button to the right of the zero, non the SELECT button. You lot should get a message that the remote is at present set for RF.
If you have other settings similar Idiot box book, you should now be able to plan them through the menus.
If nothing works
You might need a new remote. Luckily you'll find the best selection and unheard-of prices when you shop at Solid Signal.
Source: https://blog.solidsignal.com/tutorials/how-to-reset-any-directv-remote-control/
0 Response to "New Directv Box How to Get Remote to Work Again"
Post a Comment